|
Eliminator Varmint Proof Spinner Plate!
Feeder Timers & Accessories
|
$ 39.00
|
|
Stop wasting corn and start saving serious cash! This spinner plate will put an immediate stop to your corn thieves forever! This scatter plate is simply that, a scatter plate. Just remove your old plate and slip on this new spinner plate to halt your corn loss from wind, birds, squirrels, cows, hogs and yes, raccoons! You will be amazed at how long your feeder will last between fillups and yes this plate throws as good as or better than most any plate out there as well.Currently this plate will only work on ¼ shafts without adapters. Typically most 12 volt systems have a ¼ inch motor shaft.
|
|
|
|
|
|
Pro Spinner Plate for 1/4 inch Hub
Feeder Timers & Accessories
|
$ 22.00
|
|
The Pro Spinner Plate was created with 4 spring-hinged doors that open with the centrifugal force of the feeder motor and dispense the feed. When the motor stops, the doors move up into their original position creating a barrier around the down-spout to eliminate unnecessary loss of feed due to high winds, birds, scavengers, and regular feeder movements.
|
|
|
|
Pro Spinner Plate for 1/8 inch Hub
Feeder Timers & Accessories
|
$ 21.99
|
|
The Pro Spinner Plate was created with 4 spring-hinged doors that open with the centrifugal force of the feeder motor and dispense the feed. When the motor stops, the doors move up into their original position creating a barrier around the down-spout to eliminate unnecessary loss of feed due to high winds, birds, scavengers, and regular feeder movements.
|
|
|
|
Sharks Teeth Varmint Protection
Feeder Timers & Accessories
|
$ 19.99
|
This is ''IT''! No more need for varmint guards, traps, PVC pipes & cages. Shark Teeth work on the principle of abstinence. If they can't touch it, climb it, bump it or lick it; they can't tear it up, knock it over, eat up your feed or waste it! Shark Teeth come in 36'' strips that are 1 1/2'' wide. There are three to a set, and the set includes three self tapping screws per strip (9 total). Each strip has 4 parting lines 6'' apart. Each 6'' strip has 4 pre-punched holes. You can apply complete 36'' strips to feeder legs. Apply smaller pieces to Protein/Gravity Feeders heads or Control/Timer Boxes to create a barrier that repels just about anything!
|
|
|
|
Sneaky Feed
Feeder Timers & Accessories
|
$ 149.00
|
Sneaky Feed by Advanced Hunting Technologies allows you to manage any game feeder with wireless or bluetooth technology. Remotely monitor your battery voltage and your last feed time, or make a feed time change without disturbing your feeder and scenting up your most delicate hunting area!
Use your iPhone or Droid Device to check your battery level and feeder status and never blow another hunt again.
|
|
|
|
|
|
|
|
|
|
|
|
The -Timer
Feeder Timers & Accessories
|
$ 59.99
|
|
The best digital timer on the market! 5 year warranty, easiest to operate and Works with all existing control units 6 or 12 volts. *Click product photo to learn more!
|
|
|
|
The Redneck
Feeder Timers & Accessories
|
$ 39.99
|
The Redneck Timer - Easy to operate with a 5 year warranty. Compatible with any 6 or 12 volt control unit. Can feed up to 24 times a day. Timer runs on main battery only - No AA batteries needed. Fuse protected with easy 4 wire hook up, 2 to battery, 2 to motor. Uses the same harness as The-Timer.
|
|
|
|
|
|
|
|
|
|
Large Round Varmint Cage
Feeder Timers & Accessories
|
$ 39.95
|
Large Round Varmint Cage. Comes with mounting hardware. Oversized round varmint cage for protecting your control unit and precious golden nuggets. This round varmint cage attaches to the bottom of a 55-gallon (or larger) barrel and keeps the squirrels and coons from spinning your feeder empty! The cage measures 21'' in diameter by 13'' deep. There is a hinged door to provide access to your control unit.
|
|
|
|
The Remote
Feeder Timers & Accessories
|
$ 99.95
|
Wireless 175 yard remote control operation for 6 or 12 volt feeders. ULTRA-low Power Consumption! The ultimate day time or night time pig hunting tool! Keep them coming back in for another shot!
Easy installation!
Don't be fooled by the $30 big box store feeder remote controls. If you think you are getting a better deal there, think again. Be prepared to also purchase 2-3 extra solar panels to insure your feeder battery will not be dead a month after you hook it up. You get what you pay for and this remote is the best one on the market! No extra solar panels needed with this bad boy!
|
|
|
[1]_m.jpg)
|
Wireless 12 volt Feeder Remote
Feeder Timers & Accessories
|
$ 49.99
|
|
This is our popular 175 yard wireless remote designed for our Kill Lights but also works great for remote operation of a standard corn feeder or road feeder. No more wires strewn across your ATV or vehicle. This remote has an on and an off button unlike other remotes which can only activate the feeder for 5 seconds everytime you press the button. Only 7 milliamps of draw in standby
|
|
|
[2]_m.jpg)
|
Wireless 6 Volt Feeder Remote
Feeder Timers & Accessories
|
$ 49.99
|
|
This is our popular 175 yard wireless remote designed for our Kill Lights but also works great for remote operation of a standard corn feeder or road feeder. No more wires strewn across your ATV or vehicle. This remote has an on and an off button unlike other remotes which can only activate the feeder for 5 seconds everytime you press the button. Only 7 milliamps of draw in standby
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Bolt On Leg Brackets for Feeder with Hardware
Feeder Timers & Accessories
|
$ 29.99
|
|
1'' square steel stub legs that bolt onto a metal feeder barrel. Used for attaching your feeder legs. These come in handy if you want to save money and build your own feeders or need to replace old stub legs. Set of 3 and includes hardware. Legs are painted black and are 28'' in total length. The section that receives the legs is 18'' long.
|
|
|
|
|
|
Heavy Duty Belly Band
Feeder Timers & Accessories
|
$ 54.99
|
|
For the do-it-yourself feeder builder! This heavy duty belly band easily clamps around your metal barrel. No drilling required! Has three stub legs that are 20'' long. Accepts legs that are at least 1 1/4'' ID.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pages: | 1 |
|
